MCB keeps tripping at home? Causes and fixes for homes in Siliguri, Alipurduar and Raiganj
MCB keeps tripping? It's usually overload, a short circuit or a loose connection. Unplug everything, reset once, then add appliances one by one to find it.
If your MCB keeps tripping at home, the cause is usually one of three things: too much load on that circuit, a short circuit in the wiring or an appliance, or a loose, overheated connection. Switch off and unplug everything on that circuit, reset the MCB once, then plug things back in one at a time to find the culprit. If it trips again with nothing connected, stop resetting it and call a licensed electrician.
In winter this question comes up a lot in Siliguri, Alipurduar and Raiganj, when room heaters, geysers and irons all run on circuits that were wired for lights and a TV. The same checks apply to homes and shops anywhere in North Bengal, Bihar and Sikkim.
Why does my MCB keep tripping again and again?
An MCB (miniature circuit breaker) has two jobs. It trips slowly when a circuit carries more current than its rating for too long (overload), and it trips instantly when current shoots up because of a short circuit. It does not trip for earth leakage or shock — that is the RCCB’s job. If the switch that keeps dropping is the RCCB (the wider one with a “T” test button), read our guide on RCCB keeps tripping at home instead.
The common reasons an MCB trips:
| What you notice | Likely cause | What to do |
|---|---|---|
| Trips a few minutes after heater, geyser or AC comes on | Overload — total load is more than the MCB rating | Move one heavy appliance to another circuit |
| Trips the instant you switch on one appliance | Short circuit inside that appliance or its plug | Stop using it, get it checked |
| Trips even with every appliance unplugged | Short in the wiring, a burnt switch or socket | Leave it off, call an electrician |
| Trips at random, MCB or DB feels warm, burning smell | Loose or burnt connection at MCB, socket or joint | Switch off main, call an electrician today |
| Trips during rain or after water leakage | Water in a switch box, junction or outdoor light | Keep it off until the point dries and is sealed |
| Old MCB trips at light load, will not stay on | MCB worn out or wrong rating fitted | Replace with the correct rating and curve |
How do I find which appliance is tripping the MCB?
Do this calmly, one step at a time:
- Switch off and unplug everything on the circuit that tripped.
- Push the MCB back up to ON. If it will not stay on, or trips straight away, the fault is in the wiring. Stop here and call an electrician.
- If it stays on, plug in and switch on appliances one by one, with a minute or two between each.
- When it trips, the last appliance you added is either faulty or is the one that pushed the circuit over its limit.
- Try that appliance alone. If it trips alone, the appliance has a fault. If it works alone, the circuit was simply overloaded.
Do not keep resetting an MCB over and over. Each trip on a short circuit puts stress on the wiring and the breaker. Never tape an MCB in the ON position, put a bigger MCB on the same thin wire, or bypass it with a wire link. The MCB is protecting the wire inside your wall from overheating and catching fire.
MCB tripping when the heater or geyser is on — is it overload?
Usually yes. A simple way to check is to add up the watts on that circuit and divide by 230 to get amps:
| Appliance (typical rating) | Approx. current at 230 V |
|---|---|
| LED lights and fans, whole room | Under 1 A |
| Room heater, 2,000 W | About 9 A |
| Geyser, 2,000 W | About 9 A |
| Geyser, 3,000 W | About 13 A |
| Electric iron, 1,000 W | About 4.5 A |
| 1.5 ton split AC (running) | About 6–8 A, more while starting |
| Induction cooktop, 2,000 W | About 9 A |
The amps for heaters, geysers and irons are simple arithmetic (watts ÷ 230). The AC figure is a general range; check the label on your unit.
So a 2,000 W heater and a 1,000 W iron together draw about 13–14 A. On a 10 A MCB feeding 1.5 sq mm wire, that will trip — and it should. The fix is not a bigger MCB. The fix is a separate 16 A circuit on 2.5 sq mm copper wire with a 16 A socket for the heater or geyser. Our guide on room heater socket 6A or 16A explains the socket, wire and MCB sizes.
Can I just fit a higher amp MCB so it stops tripping?
No. This is a common and dangerous mistake. The MCB rating must match the wire, not the appliance. If you fit a 20 A or 32 A MCB on wire meant for 10 A, the wire can overheat inside the wall before the MCB ever trips. That is how wiring fires start.
As a rough guide used in Indian home wiring (general practice — your electrician will confirm for your run length and installation):
| Copper wire size | Usual MCB rating | Typical use |
|---|---|---|
| 1.0 sq mm | 6 A | Light points |
| 1.5 sq mm | 6–10 A | Lights, fans, small sockets |
| 2.5 sq mm | 16 A | Power sockets, heater, geyser, 1–1.5 ton AC |
| 4.0 sq mm | 20–25 A | 2 ton AC, larger geyser, kitchen power |
| 6.0 sq mm | 32 A | Sub-main to a floor or flat DB |
If you really need more load, the circuit has to be rewired with the right wire size, or the load split across circuits. Your electrician can size this for each circuit.
Which MCB curve should I use — B or C?
MCBs made to IS/IEC 60898-1 come in trip curves. A B-curve MCB trips instantly at roughly 3–5 times its rating, a C-curve at roughly 5–10 times. For most homes:
- B curve — lights, fans, heaters, geysers and normal sockets (no big starting current).
- C curve — ACs, refrigerators, pumps, motors and anything with a starting surge.
If a B-curve MCB trips only for a second when an AC compressor or pump starts, the curve may be wrong for that circuit. Ask your electrician to check before changing it.
Is my MCB faulty? How do I know when to replace it?
MCBs do wear out, especially cheap or fake ones. Signs it is time to replace:
- It trips at a load well below its rating, even after the circuit and appliances check out fine.
- The lever feels loose, will not latch, or the body is cracked, brown or melted.
- The terminal screws are blackened or the DB smells of burning plastic.
- It has no ISI mark or brand, or the rating printing has rubbed off.
Burnt terminals are often a loose connection, not just a bad MCB, so the wire end must be cut back and re-terminated properly. In our humid monsoon and damp winters across North Bengal, loose and corroded screws in old DBs are a regular cause of random tripping.
What should I tell the electrician or the shop?
Note these before you call — it saves time and gets you the right part:
- Which MCB trips, and what is printed on it (for example “C16” or “B10”, brand).
- What was running when it tripped, and whether it trips with nothing plugged in.
- Single-phase or three-phase supply, and how old the wiring is.
- Whether the DB has an RCCB and spare ways for a new circuit.
Ordering tip
If your electrician says you need new MCBs, an RCCB, a bigger DB or a fresh 16 A circuit for a heater or geyser, send Shree Shyam Suppliers a WhatsApp with: the MCB ratings and curves (e.g. 2 × C16, 4 �� B10), pole count (SP, DP, TPN), brand you prefer, wire size and length in metres, number of sockets, and your location. We will send an itemised quote with today’s rate. As an authorised dealer for Havells and Lauritz Knudsen (L&T), Shree Shyam Suppliers gives you genuine, ISI-marked MCBs and switchgear, wire cut to length and everything else for the job from one counter.
Quick answers
Why does my MCB trip when I switch on the heater?
Most often the circuit is overloaded: a 2,000 W heater draws about 9 A, and with other appliances on the same 10 A circuit the MCB trips. Run the heater on its own 16 A circuit with 2.5 sq mm copper wire.
Can I replace a 10A MCB with a 16A or 20A MCB to stop tripping?
Not unless the wire is sized for it. The MCB protects the wire; a bigger MCB on thin wire lets the wire overheat. Ask a licensed electrician to check the wire size first.
MCB trips even when nothing is plugged in. What does it mean?
It usually means a short or damaged insulation in the wiring, a burnt switch or socket, or water in a box. Leave it off and call an electrician instead of resetting it again and again.
What is the difference between MCB tripping and RCCB tripping?
An MCB trips on overload or short circuit; an RCCB trips on earth leakage, such as a leaking appliance or damp wiring. Check which device has dropped before you start looking for the fault.
How long does an MCB last?
A good ISI-marked MCB lasts many years, but heat, loose terminals and repeated short-circuit trips wear it out. Replace it if it trips at low load, will not latch, or looks burnt.
See the products: Switchgear & protection